[Jan 11, 2024] Free Cisco Meraki Solutions Specialist 500-220 Official Cert Guide PDF Download
Cisco 500-220 Official Cert Guide PDF
Cisco 500-220 exam is an important certification for IT professionals who want to demonstrate their expertise in deploying and managing Cisco Meraki solutions. Engineering Cisco Meraki Solutions certification is recognized globally and is highly valued by employers in the IT industry. Candidates who pass the exam are equipped with the skills and knowledge necessary to deploy and manage Cisco Meraki solutions efficiently and effectively, which can lead to career advancement and higher salaries.
To prepare for the Cisco 500-220 exam, candidates can take the Cisco Meraki Solutions Specialist training course. 500-220 course covers all the topics included in the exam and provides hands-on experience in deploying and managing Cisco Meraki solutions. Candidates can also use study guides and practice exams to prepare for the exam.
NEW QUESTION # 39
Drag and drop the descriptions from the left onto the permission types on the right.
Answer:
Explanation:
NEW QUESTION # 40
Which two primary metrics does Meraki Insight use to calculate the Application Performance Score? (Choose two.)
- A. Maximum Latency
- B. Maximum Jitter
- C. Application Response Time
- D. Per-flow Goodput
- E. Total Bandwidth Usage
Answer: C,D
NEW QUESTION # 41
Refer to the exhibit.
Assuming this MX has established a full tunnel with its VPN peer, how will the MX route the WebEx traffic?
- A. WebEx traffic will prefer WAN 2 as long as it is up.
- B. WebEx traffic will prefer WAN 1 as it is the primary uplink.
- C. WebEx traffic will be load-balanced between both active WAN links.
- D. WebEx traffic will prefer WAN 2 as long as it meets the thresholds in the "Conf" performance class.
Answer: B
NEW QUESTION # 42
Refer to the exhibit.
The VPN concentrator is experiencing issues. Which action should be taken to ensure a stable environment?
- A. Add a deny any/any firewall rule to the end of the firewall rules.
- B. Remove the connection from Internet 1.
- C. Configure the MX appliance to Routed mode on the Addressing & VLANS page.
- D. Physically disconnect all LAN ports.
Answer: D
Explanation:
Explanation
Before deploying MXs as one-arm VPN concentrators, place them into Passthrough or VPN Concentrator mode on the Addressing and VLANs page. In one-armed VPN concentrator mode, the units in the pair are connected to the network "only" via their respective 'Internet' ports. Make sure they are NOT connected directly via their LAN ports. Each MX must be within the same IP subnet and able to communicate with each other, as well as with the Meraki dashboard. Only VPN traffic is routed to the MX, and both ingress and egress packets are sent through the same interface.
https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best
NEW QUESTION # 43
Which Cisco Meraki best practice method preserves complete historical network event logs?
- A. Configuring the preserved event period to unlimited.
- B. Configuring the preserved event number to maximize logging.
- C. Configuring Dashboard logging to preserve only certain event types.
- D. Configuring a syslog server for the network.
Answer: B
NEW QUESTION # 44
Which configuration step is necessary when automatic updating is required of iOS apps provisioned through Systems Manager that are found in the App Store?
- A. Create a profile with automatic update enabled and apply it to iOS devices.
- B. Create a security policy that enables automatic updates.
- C. No configuration step is necessary; automatic updating is the default behavior.
- D. Configure automatic updating of iOS devices in the Meraki installed profile.
Answer: C
Explanation:
Explanation
By default, iOS apps provisioned through Systems Manager that are found in the App Store will self-update if automatic updates has been turned on in the Settings. For custom iOS apps, or to manually push down updates, check the following steps.
https://documentation.meraki.com/SM/Apps_and_Software/Updating_Managed_iOS_Apps
NEW QUESTION # 45
There will be 100 concurrent users streaming video to their laptops. A 30/70 split between 2.4 Ghz and 5 Ghz will be used. Roughly how many APs (rounded to the nearest whole number) are needed based on client count?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Explanation
This is the approximate number of APs that are needed based on client count, assuming that each AP can support up to 25 concurrent video streaming users. This can be calculated by using the formula:
Number of APs = (Number of Users x Percentage of Users on a Band) / Number of Users per AP on that Band Where Number of Users is 100, Percentage of Users on 2.4 Ghz is 30%, Percentage of Users on 5 Ghz is 70%, Number of Users per AP on 2.4 Ghz is 15, and Number of Users per AP on 5 Ghz is 30. Therefore, Number of APs = (100 x 0.3 / 15) + (100 x 0.7 / 30) Number of APs = (3.33) + (2.33) Number of APs = 5.66 Rounding to the nearest whole number, the number of APs is 4.
This question is related to the topic of Wireless Capacity Planning in the Cisco Meraki documentation. You can find more information about this topic in the [Wireless Capacity Planning] article or the [Best Practice Design - MR Wireless] page.
NEW QUESTION # 46
One thousand concurrent users stream video to their laptops. A 30/70 split between 2.4 GHz and 5 GHz is used.
Based on client count, how many APs (rounded to the nearest whole number) are needed?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 47
Refer to the exhibit.
Which condition or conditions will cause the "All Databases & cloud services" SD-WAN traffic to be routed via a VPN2 tunnel on WAN2?
- A. WAN1 tunnel latency is 20 ms or less, irrespective of WAN2 tunnel performance.
- B. WAN1 tunnel latency is 20 ms or more, and WAN2 tunnel meets the configured performance criteria.
- C. WAN1 tunnel latency is 20 ms or less, and WAN2 tunnel meets the configured performance criteria.
- D. WAN1 tunnel latency is 20 ms or more, irrespective of WAN2 tunnel performance.
Answer: B
Explanation:
Explanation
This is because the SD-WAN policy for "All Databases & cloud services" has the following settings:
Uplink selection policy: Prefer WAN1, Fail over if down
Traffic filters: Custom performance classes
Custom performance classes: Database
Database performance criteria: Maximum latency 200 ms, Maximum jitter 20 ms, Maximum loss 1% This means that the SD-WAN traffic will be routed via WAN1 by default, unless WAN1 is down or fails to meet the database performance criteria. In that case, the traffic will be routed via WAN2, if WAN2 meets the database performance criteria. Therefore, the condition that will cause the traffic to be routed via WAN2 is when WAN1 tunnel latency is 20 ms or more (which exceeds the maximum jitter of 20 ms), and WAN2 tunnel meets the configured performance criteria (maximum latency 200 ms, maximum jitter 20 ms, maximum loss
1%).
NEW QUESTION # 48
Where should a network admin navigate to investigate wireless mesh information between Meraki APs?
- A. Wireless > Monitor > RF Spectrum
- B. Wireless > Monitor > Access Points > AP > RF
- C. Wireless > Configure > Radio Settings
- D. Wireless > Monitor > Wireless Health
Answer: B
Explanation:
Explanation
See Monitoring Mesh section Mesh monitoring tools are located at the bottom of every AP detail page, which can be accessed by navigating to Wireless > Monitor > Access Points, then clicking on an Access Point.
https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Wireless_Mesh_Networking
NEW QUESTION # 49
Which type of authentication protocol is used when using OSPF on an MX appliance?
- A. plaintext
- B. certificate
- C. MD5
- D. SHA-1
Answer: C
Explanation:
Reference:
Using_OSPF_to_Advertise_Remote_VPN_Subnets
NEW QUESTION # 50
Refer to the exhibit.
Which two actions are required to optimize load balancing asymmetrically with a 4:1 ratio between links?
(Choose two.)
- A. Add an internet traffic preference that defines the load-balancing ratio as 4:1.
- B. Enable load balancing.
- C. Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1.
- D. Change the primary uplink to "none".
- E. Set the speed of the cellular uplink to zero.
Answer: B,C
Explanation:
Explanation
To clarify, to optimize load balancing asymmetrically with a 4:1 ratio between links, two actions that are required are:
Enable load balancing: This option allows the MX to use both of its uplinks for load balancing. When load balancing is enabled under Security & SD-WAN > Configure > SD-WAN & Traffic shaping, traffic flows will be distributed between the two uplinks proportional to the WAN 1 and WAN 2 bandwidths specified under Uplink configuration1.
Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1: The assigned speed of a WAN link is a value that indicates the bandwidth available on that link. By changing the assigned speeds of WAN 1 and WAN 2 so that they reflect the desired load-balancing ratio, the administrator can ensure that the MX uses both links efficiently and proportionally1. For example, if WAN 1 has a bandwidth of 100 Mbps and WAN 2 has a bandwidth of 25 Mbps, then setting their assigned speeds to
100 Mbps and 25 Mbps respectively will achieve a 4:1 load-balancing ratio.
NEW QUESTION # 51
Refer to the exhibit.
Which outcome occurs when logging is set to Enabled?
- A. The hits counter within this section is now enabled.
- B. Outbound flows are sent to a configured syslog server if a syslog sender is configured for flows.
- C. Inbound flows are sent to a configured syslog server if a syslog server configured for flows.
- D. This firewall rule is now enabled.
Answer: C
NEW QUESTION # 52
What occurs when a configuration change is made to an MX network that is bound to a configuration template?
- A. The template configuration overrides the configuration change in the bound network.
- B. The configuration change in the bound network overrides the template configuration.
- C. The more restrictive configuration is preferred.
- D. The configuration change in the bound network is combined with the template configuration inside the template.
Answer: D
Explanation:
Reference:
Managing_Multiple_Networks_with_Configuration_Templates
NEW QUESTION # 53
Which requirement is needed to implement Fast Lane on Cisco Meraki APs?
- A. traffic shaping rule tagging traffic with a DSCP value of 46 to Apple.com
- B. adaptive 802.11r disabled
- C. wireless profile installed on a Cisco iOS access point
- D. wireless profile installed on an Apple iOS device
Answer: D
Explanation:
Reference:
Wireless_QoS_and_Fast_Lane
NEW QUESTION # 54
What are two ways peers interact with ports that Auto VPN uses? (Choose two.)
- A. For IPsec tunneling, peers use high TCP ports within the 32768 to 61000 range.
- B. For IPsec tunneling, peers use UDP ports 500 and 4500.
- C. Peers contact the VPN registry at UDP port 9350.
- D. For IPsec tunneling, peers use high UDP ports within the 32768 to 61000 range.
- E. Peers contact the VPN registry at TCP port 9350.
Answer: C,D
Explanation:
Explanation
Ports used to contact the VPN registry:
- Source UDP port range 32768-61000
- Destination UDP port 9350 or UDP port 9351
Ports used for IPsec tunneling:
- Source UDP port range 32768-61000
- Destination UDP port range 32768-61000
https://documentation.meraki.com/MX/Site-to-site_VPN/Meraki_Auto_VPN_-_Configuration_and_Troubleshoo
NEW QUESTION # 55
When an SSID is configured with Sign-On Splash page enabled, which two settings must be configured for unauthenticated clients to have full network access and not be allow listed? (Choose two.)
- A. RADIUS for splash page settings
- B. Simultaneous logins
- C. Captive Portal strength
- D. Firewall & traffic shaping
- E. Controller disconnection behavior
Answer: C,E
Explanation:
Explanation
To clarify, when an SSID is configured with Sign-On Splash page enabled, the two settings that must be configured for unauthenticated clients to have full network access and not be allow listed are:
Controller disconnection behavior: This setting determines how the clients are treated when the Meraki cloud controller is unreachable. The options are Restricted or Unrestricted. The former option blocks all traffic from unauthenticated clients until the controller is reachable again. The latter option allows unauthenticated clients to access the network without signing on until the controller is reachable again1.
Captive Portal strength: This setting determines how often the clients are redirected to the splash page for authentication. The options are Block all access until sign-on is complete or Allow non-HTTP traffic prior to sign-on. The latter option allows unauthenticated clients to access other protocols such as DNS, DHCP, ICMP, etc., but blocks HTTP and HTTPS traffic until they sign on. This option is recommended for compatibility with devices that do not support web-based authentication1.
NEW QUESTION # 56
Which information do the MXs in a High Availability pair share?
- A. time synchronization state
- B. spanning-tree state
- C. DHCP association database
- D. stateful firewall database
Answer: B
NEW QUESTION # 57
How is high-availability supported for Cisco Meraki devices?
- A. An active/active high-availability pair is recommended for MX Security Appliances.
- B. Only the MX Security Appliances that use VRRP support high availability.
- C. The MX Security Appliances and MS Series Switches that use HSRP support an active/passive high- availability pair.
- D. The MX Security Appliances and MS Series Switches that use VRRP support an active/passive high- availability pair.
Answer: B
Explanation:
Reference:
_High_Availability_Pair
NEW QUESTION # 58
What are two roles of the network and device tags in a Dashboard? (Choose two.)
- A. Tags enable administrators to configure a combination of network and device specific tags to create summary reports filtered for specific devices across multiple networks.
- B. Network tags can be used to simplify the assignment of network-level permissions in an Organization with many networks.
- C. Device tags can be used to simplify the assignment of device-level permissions in an Organization with many administrators.
- D. Device tags can be assigned to MR APs to influence the gateway selection for repeaters in a mesh wireless network.
- E. Network tags can be used to assign networks to separate Auto VPN domains in an Organization with many networks.
Answer: A,B
Explanation:
Explanation
See Permissions by Network Tag section To simplify the assignment of network-level permissions in an organization with many networks, permissions can be granted to users for a given network tag.
https://documentation.meraki.com/General_Administration/Managing_Dashboard_Access/Managing_Dashboard The Organization > Configure > Manage Tags page allows Administrators to configure a combination of Network and Device specific tags to create Summary Reports filtered for specific devices across multiple networks.
https://documentation.meraki.com/General_Administration/Organizations_and_Networks/Organization_Menu/M
NEW QUESTION # 59
What is the best practice Systems Manager enrollment method when deploying corporate-owned iOS devices?
- A. manual
- B. DEP
- C. Sentry enrollment
- D. Apple Configurator
Answer: D
NEW QUESTION # 60
......
Cisco 500-220 exam is a comprehensive exam that covers a wide range of topics related to Cisco Meraki Solutions. It tests an individual's ability to design, deploy, and manage networks using the latest technologies and methodologies. 500-220 exam is intended for professionals who have experience in networking and have a good understanding of the Cisco Meraki platform.
Free 500-220 Exam Dumps to Improve Exam Score: https://dumps4download.actualvce.com/Cisco/500-220-valid-vce-dumps.html