Latest Cisco 350-501 PDF and Dumps (2023) Free Exam Questions Answers
Pass Your CCNP Service Provider 350-501 Exam on Nov 08, 2023 with 373 Questions
NEW QUESTION # 144
Refer to the exhibit.
A network operator working for a telecommunication company with an employee ID: 4350:47:853 must implement an IGP solution based on these requirements:
* Subnet 10.50.10.0 traffic must exit through the R1 router to connect with the Syslog server.
* Subnet 10.50.20.0 traffic must exit through the R2 router to connect with the NTP server.
* In case of link failure between R2 and R4, traffic must be routed via R1 and R3.
Which two configurations must be implemented on R5 to meet these requirements? (Choose two.)
- A. Apply a route policy to redistribute 10.50.0.0 prefixes in OSPF to ISIS and ISIS to OSPF.
- B. Apply a route policy to redistribute 10.50.20.0 from ISIS-L2 to OSPF Area 0 at a higher cost.
- C. Apply a route policy to redistribute 10.50.10.0 from OSPF Area 0 to ISIS-L2 at a lower cost.
- D. Enable a route policy to advertise 10.50.10.0 In OSPF Area 0 at a low cost.
- E. Enable a route policy to advertise 10.50.20.0 in ISIS-L2 at a higher cost.
Answer: B
NEW QUESTION # 145
Refer to the exhibit. Which configuration must be implemented on router R8 so that it will establish OSPF adjacency with R5?
R5#show run | s router ospf
router ospf 1
router-id 172.16.0.5
network 192.168.0.0 0.0.63.255 area 0
R5#show run int GigabitEthernet1.58
Building configuration....
Current configuration: 245 bytes
interface GigabitEthernet1.58
description LINK TO R8 Gi1.58
encapsulation dot1Q 58
ip address 192.168.58.5 255.255.255.0
ip mtu 1600
ip ospf network point-to-point
ip ospf 1 area 0.0.0.2
end
- A. router ospf 1
network 192.168.58.0 0.0.0.255 area 0.0.0.2
interface GigabitEthernet 1.58
ip ospf network point-topoint - B. router ospf 1
network 192.168.58.0 0.0.0.255 area 2
interface GigabitEthernet 1.58
ip mtu 1600 - C. router ospf 1
network 192.168.58.0 0.0.0.255 area 0.0.0.2
interface GigabitEthernet 1.58
ip mtu 1600
ip ospf network point-to-multipoint - D. router ospf 1
network 192.168.58.0 0.0.0.255 area 0.0.0.2
interface GigabitEthernet 1.58
ip mtu 1600
ip ospf network point-to-point
ip ospf 1 area 0
Answer: C
NEW QUESTION # 146
Which QoS model allows hosts to report their QoS needs to the network?
- A. MQC
- B. DiffServ
- C. IntServ
- D. CB-WFQ
Answer: C
Explanation:
Section: Architecture
Explanation/Reference:
Explanation:
IntServ follows the signaled-QoS model, where the end-hosts signal their QoS needs to the network.
Reference:
https://www.cisco.com/en/US/technologies/tk543/tk766/technologies_white_paper09186a00800a3e2f.html
NEW QUESTION # 147
Refer to the exhibit.
Router 4 is added to the network and must be in the same area as router 1. Which NET should the engineer assign?
- A. 49.0111.0000.0000.0001.00
- B. 49.0011.0000.0000.0003.00
- C. 49.0001.0000.0000.0004.00
- D. 49.0011.0000.0000.0002.00
Answer: B
NEW QUESTION # 148
After you analyze your network environment, you decide to implement a full separation model for Internet access and MPLS L3VPN services.
For which reason do you make this decision?
- A. It enables you to choose whether to separate or centralize each individual service.
- B. It is easier to manage a system in which services are mixed
- C. It enables EGP and IGP to operate independently
- D. It requires only one edge router
Answer: C
NEW QUESTION # 149
Refer to the exhibit.
An engineer at a new ISP must configure many Cisco devices in the data center. To make the process more efficient, the engineer decides to automate the task with a REST API. Which action does this JSON script automate?
- A. Configure the IP address for the existing loopback interface.
- B. Configure a physical interface on the router with an IP address and then create a loopback interface.
- C. Configure a physical interface on the router with an IP address.
- D. Delete the existing loopback Interface and replace it with a new loopback interface.
Answer: A
NEW QUESTION # 150
Refer to the exhibit.
R101 is peering with R102 and R103, and R201 is peering with R202 and R203 using iBGP Labeled Unicast address families. The OSPF area 0 border routers are in a full iBGP Labeled Unicast mesh, and VPNv4 routes are exchanged directly between PE routers R101 and R201 through iBGP Which address family-level configuration must be applied on ABR R102 on ABR R102 to support a Unified MPLS routing architecture with partitioned IGP domains?
A)
B)
C)
D)
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: A
NEW QUESTION # 151
Refer to the exhibit:
Which effect of this configuration is true?
- A. It enables MPLS on the interface
- B. it creates a pseudowire class named Cisco
- C. It enables tagging for VLAN 12 on the interface
- D. It enables AToM on interface gigabitethemet1/0
Answer: D
NEW QUESTION # 152
Refer to Exhibit:
A network engineer must update the routing toward the web server with IP address 35.22.13.1. The primary path must be configured via the neighbor router with ID 1.1.1.1. However, local-preference configuration is not permitted on R1. Which task must the engineer perform on R1 to complete the implementation?
- A. Enable MED comparison between routes from neighbors in different AS.
- B. Set the device to ignore the conditional MED if the route originated in a different autonomous system.
- C. Implement deterministic MED to choose the best route from the different AS.
- D. Configure the device to choose the best MED from the same AS.
Answer: B
NEW QUESTION # 153
Drag and drop the functionalities from the left onto the target fields on the right.
Answer:
Explanation:
NEW QUESTION # 154 
Refer to the exhibit. A network engineer is configuring customer edge routers to finalize a L2VPN over MPLS deployment. Assume that the AToM L2VPN service that connects the two CEs is configured correctly on the service provider network.
Which action causes the solution to fail?
- A. A loopback with a /32 IP address has not been used.
- B. OSPF does not work with L2VPN services.
- C. The xconnect statement has not been defined.
- D. The routing protocol network types are not compatible.
Answer: D
Explanation:
Section: Architecture
NEW QUESTION # 155
Drag and Drop Question
Drag and drop the methods of Cisco MPLS TE tunnel traffic assignment from the left onto their characteristics on the right.
Answer:
Explanation:
NEW QUESTION # 156
Drag and drop the functions from the left onto the Path Computation Element Protocol roles on the right.
Answer:
Explanation:
NEW QUESTION # 157
Refer to the exhibit. Which condition must be met by the OSPF peer of router R1 before the two devices can establish communication?
- A. The interface on the OSPF peer must use the same key ID and key value as the configured interface
- B. The interface on the OSPF peer may have a different key ID, but it must use the same key value as the configured interface
- C. The OSPF peer must be configured as an OSPF stub router
- D. The OSPF peer must use clear-text authentication
Answer: A
Explanation:
https://networklessons.com/ospf/how-to-configure-ospf-md5-authentication
NEW QUESTION # 158
Refer to me exhibit. An engineer started lo configure a router for OSPF. Which configuration must me engineer perform on me router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: B
NEW QUESTION # 159
Refer to the exhibit.
While troubleshooting the network, a network operator with an employee id: 3812:12:993 is trying to ping XR1. Which result should the operator expect when trying to ping to an XR1 local address?
- A. ICMP traffic works at a policed rate of 19 packets every 100 ms.
- B. ICMP traffic works at a policed rate of 19 bytes per second every 100 ms
- C. All ICMP traffic is dropped.
- D. All ICMP traffic responds successfully.
Answer: D
NEW QUESTION # 160
......
350-501 Dumps for CCNP Service Provider Certified Exam Questions and Answer: https://dumps4download.actualvce.com/Cisco/350-501-valid-vce-dumps.html