Latest NSE5_FNC_AD_7.6 Exam Real Tests Free Updated Today
NSE5_FNC_AD_7.6 Real Exam Question Answers Updated [Sep 16, 2026]
Fortinet NSE5_FNC_AD_7.6 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
NEW QUESTION # 35
When configuring FortiNAC-F to manage FortiGate VPN users, an endpoint compliance policy must be created for the integration.
Why is the endpoint compliance policy necessary for this type of integration?
- A. To confirm the installed endpoint certificate
- B. To validate the VPN user credentials
- C. To designate the required agent type
- D. To validate the VPN client being used
Answer: C
Explanation:
The integration of FortiNAC-F with FortiGate VPN requires a specific policy workflow to bridge the gap between initial user authentication and full network access. When a user connects to the VPN, the FortiGate typically provides the User ID and IP address, but FortiNAC-F requires a MAC address to uniquely identify and manage the endpoint's record.
According to the FortiGate VPN Integration Guide, the Endpoint Compliance Policy is a mandatory component of this setup because it is used to designate the required agent type. Because a VPN connection is Layer 3, FortiNAC cannot "see" the MAC address through traditional SNMP or L2 polling. The compliance policy instructs the system to present a Captive Portal to the remote user, requiring them to download and run either the Persistent or Dissolvable Agent. The agent then reports the device's MAC address back to FortiNAC, allowing the system to correlate the VPN session with a host record.
Once the agent is running and the MAC is known, FortiNAC-F can evaluate the device's security posture (if scanning is configured) and send the necessary FSSO tags back to the FortiGate to lift the initial network restrictions. Without the compliance policy to enforce the agent requirement, the connection would remain in an isolated "IP-only" state with no unique hardware identity.
"The Endpoint Compliance Policy is necessary to control the agent requirement for VPN users. Create a default VPN Endpoint Compliance Policy to distribute an agent via captive portal for isolated machines. This policy allows the administrator to designate the required agent type (Persistent or Dissolvable) that will be used to collect the hardware (MAC) address and perform health scans on the remote endpoint." - FortiNAC FortiGate VPN Integration Guide: Default Endpoint Compliance Policy (Optional) Section.
NEW QUESTION # 36
When working with a FortiNAC-F Manager and cluster management, what will occur when a cluster manager recovers from a non-responsive state?
- A. It rejoins the cluster as a worker node.
- B. It will be removed from the cluster and placed in a standalone group.
- C. It automatically returns to the manager state.
- D. It will perform a health check and be demoted to standby.
Answer: A
Explanation:
The correct answer is C . In FortiNAC-F Manager clustering, the active cluster management role is the leader role, and other cluster members operate as worker nodes. Fortinet's FortiNAC-F 7.6 Manager Cluster Guide states that when a worker is promoted to leader during automatic transition, the original leader becomes a worker node when it comes back online. It also explains that a cluster has one leader and can have multiple workers, with leader/worker roles used for cluster management and heartbeat exchange.
So, if the cluster manager becomes non-responsive and another node takes over leadership, the recovered manager does not automatically reclaim the leader role. It rejoins as a worker node. Option A is wrong because recovery does not automatically remove it into a standalone group. Option B is wrong because automatic return to the previous manager/leader state would create instability and possible split-brain behavior. Option D is wrong because "standby" is not the role described for FortiNAC-F Manager clustering in this context; the documented cluster roles are leader and worker.
NEW QUESTION # 37
Refer to the exhibit.
An administrator has configured the DHCP scope for a registration isolation network, but the isolation process isn't working.
What is the problem with the configuration?
- A. The label uses a system-reserved value.
- B. The lease pool does not contain a complete subnet.
- C. The gateway defined for the scope is incorrect.
- D. The domain name server designation is incorrect.
Answer: C
Explanation:
In a FortiNAC-F deployment, the configuration of the DHCP scope for isolation networks (Registration, Remediation, etc.) must perfectly align with the underlying network infrastructure to ensure that isolated hosts can communicate with the FortiNAC appliance. In the provided exhibits, there is a clear discrepancy between the DHCP configuration and the Network Topology.
As shown in the "Network Topology" exhibit, the Registration Network resides on a router interface (or sub-interface) with the IP address 192.168.180.1. This address represents the default gateway for any host placed into the Registration VLAN. However, the "DHCP configuration" exhibit shows the scope "REG-ScopeOne" configured with a Gateway of 10.0.1.254. This 10.0.1.254 address belongs to the management/service network (port2 of FortiNAC), not the registration subnet. If a host in the Registration VLAN receives this incorrect gateway via DHCP, it will attempt to send all off-link traffic to an unreachable IP, preventing it from loading the Captive Portal or communicating with the FortiNAC server.
According to the FortiNAC-F Configuration Wizard Reference, when defining a Layer 3 network scope, the "Gateway" field must contain the IP address of the router interface that acts as the gateway for that specific isolation VLAN. The FortiNAC appliance itself usually sits on a different subnet, and traffic is directed to it via the router's DHCP Relay (IP Helper) and DNS redirection.
"When configuring scopes for a Layer 3 network, the Gateway value must be the IP address of the router interface for that subnet. This allows the host to reach its local gateway to route traffic. If the gateway is misconfigured, the host will be unable to reach the FortiNAC eth1/port2 interface for registration... Ensure the Gateway matches the network topology for the isolation VLAN." - FortiNAC-F Configuration Wizard Reference Manual: DHCP Scopes.
NEW QUESTION # 38
A user was attempting to register their host through the registration captive portal. After successfully registering, the host remained in the registration VLAN. Which two conditions would cause this behavior?
(Choose two.)
- A. There is no agent installed on the host.
- B. The port default VLAN is the same as the Registration VLAN.
- C. There is another unregistered host on the same port
- D. The wrong agent s installed.
Answer: B,C
Explanation:
The process of moving a host from aRegistration VLANto aProduction VLAN(Access VLAN) is a fundamental part of the FortiNAC-F " VLAN steering " workflow. When a host successfully registers via the captive portal, FortiNAC-F evaluates its Network Access Policies to determine the correct VLAN. If the host remains stuck in the Registration VLAN despite a successful registration, it is typically due to port-level restrictions or the presence of other unregistered devices.
The two most common reasons for this behavior as per the documentation are:
The port default VLAN is the same as the Registration VLAN:If the " Default VLAN " field in the switch port
' s model configuration is set to the same ID as the Registration VLAN, the port will not change state because FortiNAC-F believes it is already in its " normal " or " forced " state.
There is another unregistered host on the same port:FortiNAC-F maintains the security posture of the physical port. If multiple hosts are connected to a single port (e.g., via a hub or unmanaged switch) and at least one host remains " Rogue " (unregistered), FortiNAC-F will generally keep the entire port in the isolation
/registration VLAN to prevent the unregistered host from gaining unauthorized access to the production network.
Issues with agents (A, B) typically prevent a host from completing compliance or registration but do not usually result in a " stuck " statusafterregistration has already been marked as successful in the system.
" If a port is identified as havingMultiple Hosts, and those hosts require different levels of access, FortiNAC remains in the most restrictive state (Registration or Isolation) until all hosts on that port are authorized...
Additionally, verify theDefault VLANsetting for the port; if the Default VLAN and Registration VLAN match, the system will not trigger a VLAN change upon registration. " -FortiNAC-F Administration Guide:
Troubleshooting Host Management.
NEW QUESTION # 39
Refer to the exhibits.
What would happen if the highlighted port with connected hosts was placed in both the Forced Registration and Forced Remediation port groups?
- A. Multiple enforcement groups could not contain the same port.
- B. Enforcement would be applied only to rogue hosts
- C. Only the higher ranked enforcement group would be applied.
- D. Both types of enforcement would be applied
Answer: C
Explanation:
In FortiNAC-F, Port Groups are used to apply specific enforcement behaviors to switch ports. When a port is assigned to an enforcement group, such as Forced Registration or Forced Remediation, FortiNAC-F overrides normal policy logic to force all connected adapters into that specific state. The exhibit shows a port (IF#13) with "Multiple Hosts" connected, which is a common scenario in environments using unmanaged switches or hubs downstream from a managed switch port.
According to the FortiNAC-F Administrator Guide, it is possible for a single port to be a member of multiple port groups. However, when those groups have conflicting enforcement actions-such as one group forcing a registration state and another forcing a remediation state-FortiNAC-F utilizes a ranking system to resolve the conflict. In the FortiNAC-F GUI under Network > Port Management > Port Groups, each group is assigned a rank. The system evaluates these ranks, and only the higher ranked enforcement group is applied to the port. If a port is in both a Forced Registration group and a Forced Remediation group, the group with the numerical priority (rank) will dictate the VLAN and access level assigned to all hosts on that port.
This mechanism ensures consistent behavior across the fabric. If the ranking determines that "Forced Registration" is higher priority, then even a known host that is failing a compliance scan (which would normally trigger Remediation) will be held in the Registration VLAN because the port-level enforcement takes precedence based on its rank.
"A port can be a member of multiple groups. If more than one group has an enforcement assigned, the group with the highest rank (lowest numerical value) is used to determine the enforcement for the port. When a port is placed in a group with an enforcement, that enforcement is applied to all hosts connected to that port, regardless of the host's current state." - FortiNAC-F Administration Guide: Port Group Enforcement and Ranking.
NEW QUESTION # 40
Refer to the exhibit.
When a contractor account is created using this template, which value is set in the accounts Role field?
- A. Engineer-Contractor
- B. Accounting Contractor
- C. Eng-Contractor
- D. Contractor
Answer: A
Explanation:
The correct answer is A . In the exhibit, the Template Name is Engineer-Contractor , and the selected Role option is Use a unique Role based on this template name . That means FortiNAC-F uses the template name itself as the role value for any account created from this guest/contractor template. The study guide confirms this behavior: by default, the Role field is populated with the template name, although the administrator can alternatively select from an existing role list. It also states that the role value in the guest and contractor template populates the Role field of any account created from that template.
Option B , Eng-Contractor , is wrong because that value is entered in the Security and Access Value field, not the Role field. That value can still be used in user/host profiles or policies, but it does not populate the account Role field. Option C , Contractor , is only the Visitor Type , which controls the kind of guest
/contractor account and associated icon behavior. Option D , Accounting Contractor , is visible in the disabled Select Role dropdown, but that option is not selected because the template is configured to use a unique role based on the template name.
NEW QUESTION # 41
Two FortiNAC-F devices have been configured as a 1 + 1 HA pair. The primary server went offline and a successful failover to the secondary has occurred. What happens if the primary server comes back online?
- A. The primary server will determine that the secondary has control and power down for maintenance.
- B. The primary and secondary servers will resume communication and the secondary will maintain control.
- C. The secondary server will update the primary and the servers will load balance until an administrator forces the primary to resume full control.
- D. After five successful heartbeats between the servers, the primary server will resume control.
Answer: B
Explanation:
The correct answer is A . In a FortiNAC-F 1+1 HA deployment, failover from primary to secondary is automatic, but failback to the primary is not automatic . The study guide states that if the primary device or its network connectivity fails, the secondary assumes control automatically, but restoration of a failed-over HA deployment is a manual administrator-driven process. It further explains that after the cause of the failover is resolved, the administrator must use the Resume Control button to transfer control back to the primary server.
That means when the primary comes back online, it does not immediately take over again. The pair can resume HA communication, but the secondary remains the in-control node until an administrator deliberately returns control to the primary. Option B is wrong because FortiNAC-F 1+1 HA is active-passive, not load- balanced. Option C is wrong because the restored primary does not power itself down for maintenance.
Option D is a trap: five failed heartbeats are used in failure detection and gateway validation logic, not as an automatic failback timer. The exam point is simple: automatic failover, manual failback .
NEW QUESTION # 42
During an evaluation of state-based enforcement, an administrator discovers that ports that should not be under enforcement have been added to enforcement groups.
In which view would the administrator be able to identify who added the ports to the groups?
(Selected)
- A. The Admin Auditing view
- B. The Event Management view
- C. The Port Changes view
- D. The Security Events view
Answer: A
Explanation:
In FortiNAC-F, accountability and forensic tracking of configuration changes are managed through the Admin Auditing functionality. When an administrator performs an action that modifies the system state-such as creating a policy, changing a device's status, or adding a switch port to an Enforcement Group-the system generates an audit record. This record is essential for troubleshooting scenarios where unauthorized or accidental configuration changes have occurred, leading to unintended network behavior.
The Admin Auditing view (found under Logs > Admin Auditing) provides a comprehensive log of the "Who, What, and When" for every administrative session. Each entry includes the username of the administrator, the source IP address from which they accessed the FortiNAC-F console, a precise timestamp, and a detailed description of the modification. In the scenario described, where ports have been incorrectly added to enforcement groups, the Admin Auditing view allows a supervisor to filter by the specific "Port" or "Group" object to identify exactly which administrator executed the command.
In contrast, the Event Management view (B) is designed to monitor system and network events, such as RADIUS authentications, host connections, and SNMP trap arrivals. While it tracks system activity, it does not typically log the manual configuration changes performed by admins. The Port Changes view (C) tracks the operational history of a port (such as VLAN assignment changes and host movements) but does not attribute the administrative assignment of the port to a group. Finally, the Security Events view (D) is dedicated to alerts triggered by security rules and external threat feeds.
"Admin Auditing displays a record of all modifications made to the FortiNAC-F system by an administrator. This view includes the administrator's name, the date and time of the change, and a description of the action taken. It is the primary resource for determining which administrative user performed a specific configuration change, such as modifying port group memberships or altering policy settings." - FortiNAC-F Administration Guide: Logging and Auditing Section.
NEW QUESTION # 43
An administrator wants each department to create and manage its own contractor accounts but not be able to manage contractor accounts for other departments. What must the administrator configure to limit the sponsor
' s capabilities?
- A. The contractor ' s template
- B. The user/host profile applied to the contractor
- C. The sponsor ' s administrative profile
- D. The portal settings on the kiosk portal page
Answer: C
Explanation:
The correct answer is D . FortiNAC-F limits what a sponsor can create and manage through the administrator profile assigned to that sponsor. The study guide explains that sponsors can be restricted to specific guest or contractor templates and that the Manage Guests settings in the admin profile define whether the sponsor can manage all accounts, no accounts, or only accounts they created. It also states that allowed templates are defined in the admin profile, meaning each department can be given access only to its own contractor template.
The contractor template defines account fields, role values, authentication method, account duration, and related account properties, but it does not by itself restrict what a sponsor can manage. Portal settings control how users interact with the captive portal or kiosk page, not sponsor administrative scope. A user/host profile is used for matching users or hosts in policy decisions; it does not delegate sponsor permissions. For departmental separation, the administrator must create sponsor-specific administrative profiles that allow only the appropriate templates and account-management scope.
NEW QUESTION # 44
Refer to the exhibit.
Which devices are automatically evaluated by these device profiling rules?
- A. Rogue devices, only when they are initially added to the database
- B. Known trusted devices, each time they connect
- C. Rogue devices, each time they change location
- D. All hosts, each time they connect
Answer: A
Explanation:
The correct answer is A . In FortiNAC-F, device profiling rules are used primarily to classify unknown or untrusted devices when they are first discovered. The study guide explains that when a device does not already exist in the database, FortiNAC-F adds it, treats it as a rogue, and evaluates it against enabled device profiling rules. It also states that devices are initially evaluated against device profiling rules only if they do not already exist in the database, because this avoids unnecessary repeated evaluation of known devices.
The exhibit also matters: the rules are enabled and set to Automatic registration, but Confirm Rule On Connect is not enabled and Confirm Rule Interval is set to None . That means FortiNAC-F will not automatically revalidate already-profiled or trusted devices every time they connect. Option B is wrong because trusted devices are not repeatedly evaluated unless rule confirmation is configured. Option C is too broad because all hosts are not processed through profiling rules on every connection. Option D is also wrong because changing location does not by itself force automatic device profiling; location can be used as a rule method, but the automatic evaluation described here applies when the rogue device is initially added to the database.
NEW QUESTION # 45
Refer to the exhibit.
Given this topology, and a layer 3 registration network configuration, which IP address would be designated in the DHCP relay configuration for the registration network?
- A. 192.168.200.10
- B. 192.168.10.254
- C. 192.168.100.20
- D. 192.168.100 75
Answer: A
Explanation:
The correct answer is D . In a Layer 3 registration or isolation network design, DHCP requests from the isolated registration VLAN are not served locally on that VLAN by a normal production DHCP server.
Instead, the registration VLAN's DHCP relay must forward DHCP traffic to FortiNAC-F port2 , because port2 is the captive network service interface. The study guide states that in Layer 3 captive networks, DHCP traffic is relayed to port2 from the captive networks, and that the FortiNAC-F port2 interface provides DHCP, DNS, and captive portal services for hosts assigned to those captive networks.
In the exhibit, the registration VLAN is 192.168.10.x/24 , with gateway 192.168.10.254 . That gateway is where the DHCP relay would be configured, but it is not the relay destination. The relay destination must be the FortiNAC-F port2 address, shown as 192.168.200.10 . The corporate DHCP server 192.168.100.75 is for production network addressing, not registration isolation. The FortiNAC-F port1 address 192.168.100.20 is the administrative or production-facing interface, not the captive network service interface. Therefore, the DHCP relay should point to 192.168.200.10 .
NEW QUESTION # 46
When preparing network infrastructure devices for visibility, what are the two main advantages of using MAC notification traps on supported devices instead of link-up and link-down traps? (Choose two.)
- A. Hosts connecting to downstream non-managed hubs are immediately learned.
- B. MAC notification traps include IP address information.
- C. Overhead on FortiNAC-F and the infrastructure device is reduced.
- D. Faster visibility updates with only a slight increase in processing.
Answer: A,C
Explanation:
Comprehensive and Detailed Explanation From Exact Extract of FortiNAC-F 7.6 Administrator Guide or Knowledge:
Exact Extract:
The FortiNAC-F study guide states that MAC notification traps are preferred because FortiNAC-F does not need to connect back to the infrastructure device every time a link-up or link-down trap is received. The required MAC and port information is already included in the MAC notification trap, which makes database updates faster and uses fewer resources. It also states that hosts and devices connected through hubs or IP phones are seen immediately, even when the downstream device cannot generate link-up or link-down traps.
Technical Deep Dive:
The correct answers are B and C . With link-up/link-down traps, the trap only tells FortiNAC-F that an interface changed state. FortiNAC-F then has to perform an L2 poll against the switch forwarding table to discover which MAC address appeared or disappeared. That means extra SNMP/CLI activity, more delay, and more processing on both FortiNAC-F and the switch. The guide confirms that link traps trigger FortiNAC- F to perform a Layer 2 poll, while MAC notification traps directly contain the learned or removed MAC address and associated port.
Option A is wrong because MAC notification traps are Layer 2 visibility events. They identify MAC address and port , not IP address. IP-to-MAC correlation comes from Layer 3 polling or DHCP fingerprinting, not MAC notification traps. Option D is badly worded and should not be selected: MAC notification traps do provide faster updates, but the processing overhead is reduced, not slightly increased.
Operationally, on supported switches you enable SNMP traps for MAC address-table changes and point the trap destination to FortiNAC-F. On Cisco-style infrastructure, this is usually done with commands such as snmp-server host < FortiNAC-IP > version 2c < community > plus MAC notification trap configuration. Do not enable MAC notification traps on uplinks, because uplinks learn many downstream MAC addresses and would create misleading endpoint-location data.
NEW QUESTION # 47
During the testing of a newly modeled infrastructure switch, the administrator is not seeing hosts as they connect or move from one port to another. What would cause this issue?
- A. Contact polling is not configured.
- B. MAC notification traps are misconfigured.
- C. Layer 3 polling is failing.
- D. The default scheduled polling is disabled.
Answer: B
Explanation:
The correct answer is A . When FortiNAC-F needs near real-time Layer 2 visibility, it relies on link traps, MAC notification traps, RADIUS, or scheduled/manual Layer 2 polling. The study guide explains that MAC notification traps contain the MAC address learned or removed from the switch MAC address table and the associated port, allowing FortiNAC-F to update its database when hosts connect, disconnect, or move. It also states that MAC notification traps are the preferred method for learning and updating Layer 2 information.
If a newly modeled switch does not show hosts as they connect or move between ports, the likely problem is that MAC notification traps are not correctly configured or not reaching FortiNAC-F . Layer 3 polling failure would affect IP-to-MAC correlation, not the ability to learn which switch port a MAC address is connected to. Disabled scheduled polling could delay updates, but it would not be the best explanation when the expected behavior is immediate host detection during connection or movement testing. Contact polling only checks whether the device is reachable; it does not collect host MAC-to-port visibility.
NEW QUESTION # 48
An administrator has created several device profiling rules and evaluated all existing devices in the database. Some of the devices appear in the profiled devices view because they matched a rule, but they remain unknown and the registration column in the profiled devices view shows "No".
What is the most likely cause?
- A. The device profiling rule has registration set to manual.
- B. The devices have persistent agents installed, and the point of connection has PA optimization enabled.
- C. The confirm device profiling rule option is not enabled.
- D. The devices match more than one device profiling rule.
Answer: C
Explanation:
In FortiNAC-F, Device Profiling Rules are used to automatically identify and categorize devices (such as IP cameras, printers, or IoT devices) based on fingerprints like DHCP fingerprints, OIDs, or MAC prefixes. When a device matches a rule, it appears in the Profiled Devices view.
However, matching a rule does not automatically register the device in the database unless the rule is configured to do so. If the devices appear in the view but remain "Unknown" and show "No" in the registration column, it indicates that the "Confirm" (or "Auto-register") action has not been triggered. In the Device Profiling Rule configuration, there is a setting called "Allow Auto-Approval" or "Confirm". If this is not enabled, the system identifies the device but waits for an administrator to manually approve the match before changing the host status from "Unknown" to "Registered".
This is a common "safety" configuration used during the initial deployment phase to ensure that the profiling rules are accurate before the system begins automatically granting network access based on those matches.
"If a device matches a rule but is not registered, check the rule configuration. The Confirm option (within the Method or Rule settings) determines if the system automatically registers the device upon a match. If Confirm is not enabled, the device will remain in the 'Profiled' state with a registration status of 'No' until an administrator manually promotes the device." - FortiNAC-F Administration Guide: Device Profiling Rules.
NEW QUESTION # 49
Refer to the exhibit.
A FortiNAC-F N+1 HA configuration is shown.
What will occur if CA-2 fails?
- A. CA-3 will continue to operate as a secondary in an N+1 HA configuration.
- B. CA-3 will be promoted to a primary and share management responsibilities with CA-1.
- C. CA-1 and CA-3 will operate as a 1+1 HA cluster with CA-3 acting as a hot standby.
- D. CA-3 will be promoted to a primary and FortiNAC-F manager will load balance between CA-1 and CA-3.
Answer: A
Explanation:
In an N+1 High Availability (HA) configuration, a single secondary Control and Application (CA) server provides backup for multiple primary CA servers. The FortiNAC-F Manager (FortiNAC-M) acts as the centralized orchestrator for this cluster, monitoring the health of all participating nodes.
According to the FortiNAC-F 7.6.0 N+1 Failover Reference Manual, when a primary CA (such as CA-2 in the exhibit) fails, the secondary CA (CA-3) is automatically promoted by the Manager to take over the specific workload and database functions of that failed primary. Crucially, the documentation specifies that even after this promotion, the system architecture maintains its N+1 logic. The secondary CA effectively "assumes the identity" of the failed primary while continuing to operate within the N+1 framework established by the Manager.
It does not merge with CA-1 to form a traditional 1+1 active/passive cluster (A), nor does it engage in load balancing (D), as FortiNAC-F HA is designed for redundancy and failover rather than active traffic distribution. Furthermore, CA-3 does not "share" management with CA-1 (C); it independently handles the tasks originally assigned to CA-2. Throughout this failover state, the Manager continues to oversee the group, and CA-3 remains the designated secondary unit currently acting in a primary capacity for the downed node until CA-2 is restored.
"In an N+1 Failover Group, the Secondary CA is designed to take over the functionality of any single failed primary component within the group. The FortiNAC Manager monitors the primaries and initiates the failover to the secondary... Once failover occurs, the secondary continues to operate as the backup unit for the failed primary while remaining part of the managed N+1 HA configuration." - FortiNAC-F 7.6.0 N+1 Failover Reference Manual: Failover Behavior Section.
NEW QUESTION # 50
An administrator wants to create a conference manager administrator account but would like to limit the number of conference accounts that can be generated to 30.
Which statement about conference accounts is true?
- A. In FortiNAC-F, conference accounts can be limited by multiples of 25, so the conference administrator could create 50 accounts.
- B. The administrator can set a maximum of 30 conference accounts in the administrative profile for the conference manager.
- C. The conference account limit is defined in the onboarding conference portal.
- D. Conference account limits are defined in the conference guest and contractor template.
Answer: B
Explanation:
In FortiNAC-F, the Conference Manager is a specialized administrative role designed for delegated administration, often used by receptionists or event organizers to create temporary guest accounts. To maintain security and prevent the over-provisioning of credentials, FortiNAC-F allows for granular restrictions on these accounts.
According to the FortiNAC-F Administration Guide regarding Administrative Profiles, when an administrator creates a profile for a Conference Manager, they can define specific "Account Limits." Under the profile settings (located in System > Settings > Admin Profiles), there is a field specifically for "Max Accounts." By entering "30" into this field, the administrator ensures that any user assigned to this profile cannot exceed 30 active conference accounts at any given time.
This setting is distinct from the Portal configuration or the Guest templates. While templates define the type of account (e.g., duration and access level), the Administrative Profile defines the capabilities and limitations of the person creating those accounts. This ensures that even if a guest template allows for unlimited registrations, the specific administrator is physically restricted by the system from generating more than the allotted 30.
"Administrative Profiles define what an administrator can see and do within the system. For delegated administration roles like the Conference Manager, the 'Max Accounts' field in the Administrative Profile is used to specify the maximum number of accounts the user is permitted to create. Once this limit is reached, the user will be unable to generate additional accounts until existing ones expire or are deleted." - FortiNAC-F Administration Guide: Administrative Profiles and Delegated Administration.
NEW QUESTION # 51
Which two statements are true about integrating a third-party device using SNMP traps from that device as input to generate an event? (Choose two.)
- A. The sending device must support SNMPv3.
- B. The sending device must be modeled in the inventory topology.
- C. The IP address OID and MAC address OID must be configured in the trap MIB file.
- D. set allowaccess snmp must be configured using the CLI on the FortiNAC-F receiving interface.
Answer: B,D
NEW QUESTION # 52
An administrator wants to use FortiNAC-F to prevent internal engineers from accessing specific websites as defined in web filter categories on FortiGate. In addition to a security trigger and associated action, which configuration must also be defined on FortiNAC-F?
- A. A compliance policy
- B. A profiling method
- C. A firewall policy
- D. A user/host profile
Answer: D
Explanation:
The correct answer is C . FortiNAC-F security automation does not rely only on a trigger and action. After a security alert is received and the security trigger is satisfied, FortiNAC-F can also evaluate an associated user
/host profile before generating the security alarm and executing the action. The study guide explains that user
/host profiles are the same profiles used by security policies and are used in security rules to leverage "who, what, where, and when" visibility information. This is exactly what the question requires: the rule must apply specifically to internal engineers , not every user who triggers the FortiGate web-filter category event.
A compliance policy is wrong because compliance policies evaluate endpoint health, posture, scans, or agent results; they do not scope FortiGate web-filter-triggered automation to a user population. A firewall policy is configured on FortiGate, not as the FortiNAC-F-side matching condition in the security rule. A profiling method is also wrong because profiling methods classify rogue or unknown devices, such as printers, cameras, or phones; they do not identify internal engineers for a security automation workflow. The user/host profile is the correct FortiNAC-F object because it lets the same FortiGate security trigger produce a different response depending on the matched user, host, group, location, or ownership context.
NEW QUESTION # 53
Refer to the exhibit.
If a host is connected to a port in the Building 1 First Floor Ports group, what must also be true to match this user/host profile?
- A. The host must have a role value of contractor, an installed persistent agent or a security access value of contractor, and be connected between 6 AM and 5 PM.
- B. The host must have a role value of contractor or an installed persistent agent and a security access value of contractor, and be connected between 6 AM and 5 PM.
- C. The host must have a role value of contractor or an installed persistent agent, a security access value of contractor, and be connected between 9 AM and 5 PM.
- D. The host must have a role value of contractor or an installed persistent agent or a security access value of contractor, and be connected between 6 AM and 5 PM.
Answer: B
Explanation:
The User/Host Profile in FortiNAC-F is the fundamental logic engine used to categorize endpoints for policy assignment. As seen in the exhibit, the configuration uses a combination of Boolean logic operators (OR and AND) to define the "Who/What" attributes.
According to the FortiNAC-F Administrator Guide, attributes grouped together within the same bracket or connected by an OR operator require only one of those conditions to be met. In the exhibit, the first two attributes are "Host Role = Contractor" OR "Host Persistent Agent = Yes". This forms a single logical block. This block is then joined to the third attribute ("Host Security Access Value = Contractor") by an AND operator. Consequently, a host must satisfy at least one of the first two conditions AND satisfy the third condition to match the "Who/What" section.
Furthermore, the profile includes Location and When (time) constraints. The exhibit shows the location is restricted to the "Building 1 First Floor Ports" group. The "When" schedule is explicitly set to Mon-Fri 6:00 AM - 5:00 PM. For a profile to match, all enabled sections (Who/What, Locations, and When) must be satisfied simultaneously. Therefore, the host must meet the conditional contractor/agent criteria, possess the specific security access value, and connect during the defined 6 AM to 5 PM window.
"User/Host Profiles use a combination of attributes to identify a match. Attributes joined by OR require any one to be true, while attributes joined by AND must all be true. If a Schedule (When) is applied, the host must also connect within the specified timeframe for the profile to be considered a match. All criteria in the Who/What, Where, and When sections are cumulative." - FortiNAC-F Administration Guide: User/Host Profile Configuration.
NEW QUESTION # 54
Which two actions must the administrator perform to allow FortiNAC-F to process incoming syslog messages from an unknown vendor? (Choose two.)
- A. The device sending the messages must be modeled in the Network Inventory view.
- B. The device must have an event parser created for it.
- C. The device must be added as a log receiver in FortiNAC-F.
- D. The device must be added as a server in the Host view.
Answer: A,B
Explanation:
The correct answers are A and B . For FortiNAC-F to process syslog messages from a vendor that is not already known, it needs a parser so it can understand the message structure. The study guide describes this under syslog integration: syslog files must be created, and FortiNAC-F parses CSV, CEF, or tag/value messages by using column mapping or tag-to-value mapping. That parser is what allows FortiNAC-F to extract the correct event information from the incoming message.
The sending device must also be modeled in the Inventory view, normally as a pingable device, and its Incoming Events setting must be set to Syslog with the appropriate parser selected. The guide is blunt on this point: FortiNAC-F does not process syslog or trap messages unless the source address belongs to a modeled device.
Option C is wrong because adding the device as a server in the Host view does not prepare FortiNAC-F to parse syslog input. Option D is also wrong because log receivers are for sending FortiNAC-F event or alarm information out to external systems such as FortiAnalyzer, SIEM, or a syslog server, not for receiving and parsing unknown-vendor syslog messages.
NEW QUESTION # 55
While deploying FortiNAC-F devices in a 1+1 HA configuration, the administrator has chosen to use the shared IP address option.
Which condition must be met for this type of deployment?
- A. The primary and secondary administrative interfaces are on the same subnet.
- B. The isolation network type is Layer 2.
- C. The isolation network type is layer 3.
- D. There is a direct cable link between FortiNAC-F devices.
Answer: A
Explanation:
In a 1+1 High Availability (HA) deployment, FortiNAC-F supports two primary methods for management access: individual IP addresses or a Shared IP Address (also known as a Virtual IP or VIP). The Shared IP option is part of a Layer 2 HA design, which simplifies administration by providing a single URL or IP that always points to whichever appliance is currently in the "Active" or "In Control" state.
For a Shared IP configuration to function correctly, the Primary and Secondary administrative interfaces (port1) must be on the same subnet. This requirement exists because the Shared IP is a logical address that is dynamically assigned to the physical interface of the active unit. Since only one unit can own the IP at a time, both units must reside on the same broadcast domain (Layer 2) to ensure that ARP requests for the Shared IP are correctly answered and that the gateway remains reachable regardless of which unit is active. If the appliances were on different subnets (a Layer 3 HA design), a shared IP could not be used because it cannot "float" across different network segments; instead, administrators would need to manage each unit via its unique physical IP or use a FortiNAC Manager.
"For L2 HA configurations, click the Use Shared IP Address checkbox and enter the Shared IP Address information... If your Primary and Secondary Servers are not in the same subnet, do not use a shared IP address. The shared IP address moves between appliances during a failover and recovery and requires both units to reside on the same network." - FortiNAC-F High Availability Reference Manual: Shared IP Configuration.
NEW QUESTION # 56
......
Latest NSE5_FNC_AD_7.6 Study Guides 2026 - With Test Engine PDF: https://dumps4download.actualvce.com/Fortinet/NSE5_FNC_AD_7.6-valid-vce-dumps.html